Control Valve Partial Stroke Testing (PST) for Safety Valves

Practical Procedure · Safety Systems Control Valve Partial Stroke Testing (PST) for Safety Valves Applies to: Emergency shutdown (ESD) valves and safety instrumented function (SIF) final elements  |  Equipment needed: PST-capable positioner/logic solver, position feedback monitoring, coordination with process/operations Full Stroke vs. Partial Stroke — Why PST Exists Tap a tab to see the difference between a full functional test and a partial stroke test, and why PST lets you test without shutting down. Full Stroke Test Partial Stroke Test (PST) ESD Valve — Process Running 0% → 100% → 0% process fully interrupted during test ESD Valve — Process Running ...
Post a Comment

Contact

 Have a question about something on this blog, a troubleshooting problem you're stuck on, or feedback on an article? I'd like to hear from you.

Email: dashingboy1725@gmail.com

I try to respond to genuine technical questions and feedback where I can, though as this is a personal blog alongside full-time plant work, replies may take a few days.

For quick questions, feel free to leave a comment directly on the relevant post — it also helps other readers who might have the same issue.

Comments

Post a Comment

Popular posts from this blog

Belt weigh feeder Zero and Span Drift

Image
Fault Log · Field Report Schenck Weigh Feeder — Zero and Span Drift, Two Different Root Causes Plant: Cement  |  System: Schenck weigh feeder, belt scale, hopper load cells  |  Downtime: None Symptom A Schenck weigh feeder started showing both zero drift and span drift at the same time. Two separate accuracy problems showing up together made this a two-part investigation from the start — zero and span errors don't always share the same root cause, even when they appear together. Investigation — Zero Drift Started with the load cell loop and mechanical side of the belt scale: Load cell loop — checked the full loop, cleaned the load cell area. Idlers/rollers — checked the rollers for wear or misalignment. Belt tracking — with the belt empty, noticed it was drifting to one side. Zero was being tared in that empty, drifted position. Once material loaded onto the belt, the belt tracked back closer to center — meaning the zero reference had been tak...
Read more

Load Cell Calibration for Weigh Feeders

Image
Practical Procedure · Calibration Load Cell Calibration for Weigh Feeders — Dead-Load, Test-Weight, and Why Shunt Calibration Isn't Enough Applies to: Belt weigh feeders, weigh hoppers with load cell-based measurement  |  Equipment needed: Certified test weights or a dead-load/material reference, shunt calibration resistor (if supported), digital indicator/weigh controller access Before You Start Confirm the feeder/hopper is mechanically free — check idlers, belt tension, and load cell mounting for anything that could add friction or false load before assuming a load cell problem. Check load cell cabling and junction box connections for corrosion or loose terminations, especially in dusty or humid plant environments. Note whether the system uses a single load cell or multiple load cells summed together — multi-cell systems need each cell checked individually, not just the combined output. Method 1 — Shunt Calibration Shunt calibration simulates a known load...
Read more

Zirconia Oxygen Analyzer Reading Maximum O2

Image
Fault Log · Field Report Zirconia Oxygen Analyzer Reading Maximum O2 — Not the Cell, a Rusted Outlet Plant: Cement  |  System: Zirconia oxygen analyzer, sample extraction system  |  Downtime: None Symptom The zirconia oxygen analyzer started reading maximum oxygen — pegged at the top of the range rather than tracking the actual process value. A reading stuck at maximum on a zirconia cell usually means the cell is seeing something close to ambient air instead of process gas, which points straight at a sample delivery problem before you even think about the analyzer itself. Investigation Started at the sample path, from the process side inward: Probe, extractor filter, sampling line, pump — checked the full sample path from the probe through the extraction filter and sampling line, including the sample pump. Performed a leakage test across this section. All found ok. Panel-side tubing and membrane filter — checked all tubing inside the panel along...
Read more